MSQ Qus. for aviation engineer student

[ولد قطر]

السلام عليكم ورحمة الله وبركاته ........



هذي صفحه أقدم فيها أسئله مهمة لطلاب هندسة صيانة الطائرفي بعض المواد , وياريت ياجماعه انكم اتشاركون معانا بالأسئله الي عندكم , وبعد طلباتكم وانشاء الله بنجيبها لكم .



وشكرا



ولد قطر





ونبدا بمادة الدجتال Digital

للتحميل

http://sr1.mytempdir.com/167435

أو

http://rapidshare.de/files/5351450/Digital.zip.html


وهذي صفحه فيها بعض الاسئله من Model 1to 11وفيه كتب للأسئله وهي للبيع وممكن تستفيدون منها .

http://www.jar66.de/coaching.html



أنتظروا المزيد

[ولد قطر]

هذي بعض اسئلة الهيومن فاكتور من موديل 9
Human Factor Questions (http://www.jartraining.de/phpBB2/viewtopic.php?t=209&start=0&postdays=0&postorder=asc&highlight=)
1. The incident in 1995where a b737 lost oil pressure and had to divert was?
A) A typical human factors related error.
B) To be expected due to the number of flights each day.
C) Due to murphys law.

2. Accidents and engineering faults are
a) insignificant and increasing
b) insignificant and decreasing
c) significant and increasing


3. Information on drugs and alcohol can be found in
a) AWN 3
b) AWN 47
c) BCARs


4. 70 - 80% of the total focusing ability of the eye is carried out by
the
a) iris
b) lens
c) cornea


5. At what distance should a person without hearing difficulties be able
to hear an average conversational voice in a quiet room
a) 1 metre (3 feet)
b) 2 metres (6 feet)
c)


6. If you have been prescribed new medicine by your doctor you should
a) continue with your normal shift pattern
b) give the new medication a 24 hour trial
c) take 3 days off work to try out the new medication

[AboAyoob]

وعليكم السلام ورحمة الله وبركاته
شكرا لك اخوي ولد قطر على الموضوع الجميل جداً
واتمنى الفائدة لأصحاب الأختصاص منه
بالتوفيق أن شاء الله

[ولد قطر]

شكرا على مرورك اخ بو ايوب وانشاء الله انفيد الشباب والي شجعني لطرح الموضوع اني مالقيت مواقع كثيره للأسئله والمواقع الموجوده كلها تفشل بسرعه وانا بحاول اني اكتب الأسئله الي عندي واساعد الشباب . وانشاء الله تنجح المحاوله .

[رفيق الطيران]

السلام عليكم ورحمة الله وبركاته ,.\
الله يبارك لنا بجهودك بوجسيم ،وحاجة ابد مش غريبة عليك
في سؤال هل الاسئلة التي طرحتها مشهورة او بمعني اخر
معروفة ويتم دراستها في اماكن عدة

[مشاغب]

أخ ولد قطر موضوعك جد متميز, ألف شكر وننتظر منك المزيد.
جوابا على سؤالك أخ احمد علي فالأسئلة التي طرحها ولد قطر تدرس في كل ماهو له علاقة بالالكترونيك الرقمي والله أعلم.

[رفيق الطيران]

اشكر لك
الاخ العزيز،مشاغب علي الاهتمام والاجابة ،وكم لسررت بتسجيلك معنا

[Flying Way]

يعطيك العافيه ولد قطر شي رائع بلفعل

انا ودي ادرس هندسه طيران في السعوديه وش رايكم وكم نسبه القبول فيها

وماهي طبيعه العمل في هندسه الطيران كيف ارجوا الاجابه

[ولد قطر]

جزاكم الله خير على الردود

اخ هشام انا ما عندي اي فكره عن الدراسه فالسعوديه , لو تطرح سؤالك في قسم أكاديميات و مدارس الطيران وانشاء الله الشباب بيفيدونك .

[ولد قطر]

السلام عليكم ورحمة الله وبركاته

تحيه طيبه لكل اعضاء ومشرفين المنتدى

لقد قمت ببعض التجديد فهالمشاركة بوضع بعض الأسئله وانشاء الله شباب هندسة صيانة الطائرات يستفيدون منها .

وشكرا

يتبع

Module 11

The aircraft exterior is given HP washing, the caution is:
A. Protection treatment may be removed.
B. To check the interior of cabin compartment for water ingress.
C. To keep temperature at least 80C

Aileron control surface is given spring-tab & a balance tab
A. Directly manual control surface
B. Operate both
C. Position balance tab only

VOR receivers receive radio signal from
A. The OD signal and directly signal
B. The non-direct signal from VOR G/S
C. The VHF line-of-sight ODS from VOR/ILS.

The effect of tuck under on swept-back wing.
A. Nose down movement thoroughly
B. Nose down movement follow nose up movement.
C. Nose up movement follow nose down movement.

Double plate around door cutout
A. Control crack propagation.
B. Multi-load path design.
C. Both above.

An electronic library system:
A. Is used to remember special technical data.
B. Is can be recalled from the CMC with special access password.
C. It can be installed in OEM before airplane is delivery.

Fluorescent light used in cabin area:
A. are usually mount on dome and sidewall
B. only one intensity output from ballast transformer.
C. are powered by ground service bus.

Fuel has leaded into compartment, venting and draining arrangement are made, inspection should be placed on:
A. to residual fuel.
B. airflow through compartment.
C. the effect on fuel on other material such as cable seal and insulation.

When checking at pneumatic deicing systems verify the follow factor:
A. Suction gauge operation initial.
B. Inflate cycle of deicer longer than deflate.
C. Not of two others.

When heating is accomplished with bleed air, the cabin air is :
A. Either engine bleed or turbocharger.
B. A mix of bleed air and ambient or recirculated air.
C. Ram air or recirculated air.

Pick out the correct state.
A. The left spoiler mixer drives left side spoilers.
B. Spoiler mixer, sum two control input.
C. Ground spoiler are deployed when landing gears down.

Pipeline leading from static vents to instruments should:
A. Rise for at least 6 inches.
B. Rise continuously towards vents.
C. Be installed level and clamped adequately

One place stair way mounted on same small A/C
A. can not be used as a plug door at the same time
B. is open side way
C. is hinged on the bottom

For combustion heater system, the solenoid shut off valve which supplies fuel to heater
A. Is de-energized to reduce
B. Is energized to reduce
C. Is depend on the air flowing into the heater

The hinge installation for rudder
A. Take the form of a vertical post secured to the rear spar of fin
B. Take the form of upper and lower bearings
C. Is recessed into balance compartment of the vertical fin

The pilot valve in pressure regulator
A. Solenoid control
B. Sensed pressure change and actuate directly spool valve
C. Anticipated the pressure surge and control main valve in advance

Area rule for A/C
A. Use for delay the shock wave formation
B. Reduce wave drag to minimal
C. Reduce form drag and skin friction

When designed as a separate member the vertical fin
A. Is both removable and adjustable
B. Forms a permanent a assemble with the stabilizer
C. Is a selects preference LOC for full tank

The tie-down assembly for a galley
A. Takes the forms of quick disconnect fasteners
B. Avoids coffee and beverage spills
C. Secures against the g-force

When O/B spoiler selector are used in lateral control system
A. The left selector selects the left O/B spoiler
B. The selection is done for a symmetrical pair of spoiler on the ground
c. The selector reduces the travel range of O/B spoiler on the ground

Optimal type temperature sensor inside a thermostatic v\v for pre-cooler operation is:
A. Evacuate bellow
B. Bi-metallic element
C. Oil filled bellow


The operation of a flight control surface utilizes a scheme of HYD balance the centering and feels effect comes from:
A. The full magnitude of ram pressure and aerodynamic force
B. The net hinge movement on the control surface
C. Countering spring and artificial device

If one of the bolt is forced defective
A. Replace bolts
B. Replace the bolts and renew the complete set of wheel
C. Replace the bolt and renew all fusible plugs

Operation of fowler flap
A. Increase wing area but no camber
B. Maintain same wing load
C. Increase the fame arable pressure gradient on the wing section

Under wet take off condition followed by freezing, the structural inspection focus should be
A. oils oil leaks
B. engine intake and exhausts
C. landing gear door seal

In fulfill airworthiness, structure design must
A. Light and strong, always light alloy
B. Be damage tolerance as to facilities in time inspection and remedy
C. Be high fatigue and crack resist

Th storage life of high pressure pneumatic compartment
A. Is not limit
B. Is defined in MM
C. Is variable determined by non metal part in assembly

The part CMC that can be customized for an airline
A. Is loaded into the sys manufacture a/c delivery time
B. Can be loaded using a software data loaded in the man sequence center
C. Consist of note and help page

The pin-type pin design for wing -body joint is not commonly used for modern transport because
A. The pin-joint is too simple
B. A simple pin connection tend to cause corrosion problem
C. No fail safety provision though attachment redundancy

The advantage of TAT probe over flush bulb is that it has
A. high recovery
B. negligible time lag
C. both A and B
The head of engine fire bottle is
A. check out to pass very much reduced current through squib
B. not allow intentional thermal discharge
C. installed with explosion cartridge spot 1 and 2

Pick out the correct statement about secondary structure
A. Can take part of primary load
B. May be include class 1 structure
C. May be made of composite material

In an ACM the fan compressor turbine unit
A. Cool only by boosting ram air convection rate
B. Generally utilized on ground and for high ambient temp.
C A redundant device

A yaw may be caused by
A. Different dihedral angle
B. An oversize fin
C. A twisted fuselage

Wing fence
A. Is usually used to the root than to the tip of the wing
B. Is installed to inject energy into the boundary layer by causing vortex flow
C. Reduce tendency to wing tip vortices

Fail safe structural design
A. Is essentially dual load parts and load sharing
B. Is a scheme to ensure adequate strength under corrosion environment
C. Will not work unless coupled with adequate inspection failing


When the torque applies to a gyro is increased, the precession rate will be
A. Increased.
B. Decreased.
C. Unchanged.

Multi damage
A. Is present of same damage at alternator path
B. Is present of second damage dependent or independent primary damage
C. Is present of sever corrosion

Pneumatic component storage is
A. No limited
B. Is defined in MM
C. Variable determined by the non-metallic part

APU output pressure is 42 psi. because
A. Pneumatic duct at 45 psi when on loading
B. Above this pressure will prevent the engine crossfeed start
C. When engine start the pressure reduce fast

Which is not unit type detector?
A. Melting link and thermal couple detector
B. Differential expansion switch and central-electrode detector
C. Melting link and differential expansion switch


Potable water system
A. Pressurized sys apply from compressor with pressure system
B. Either with self -vent faucet or heated drain mask
C. Electric heater applied to all along the water line

Toilet installation
A. Flush sys only include clued flush handle, motor pump filter assembly and reuired tube
B. Stainless steel bowl are install with flexible restrictor on top of the waste tank
C. Waste tank make of glass fiber with spring loaded drain v/v

Seat install
A. All is directional
B. Forward and after
C. Only in belt active

The balancing mass for flight control surface is
A. Installed forward of the hinge line
B. To the extent of repositioning the CG at mid chord
C. Aimed to balance partially force in the system

The skid control v/v
A. Increase the brake metered pressure when skid occurs
B. Are normally closed shot off v/v
C. Are down stream and in serious with brake control v/v

Composite material flight control surface
A. Need to have drainage opening like the all -metal of surface
B. Are often completely sealed from the atmosphere
C. Are installed with rivet type fasteners


The apparent wander for directional gyro is
A. Compensate by applying a constant force
B. Max at the pole
C. Dependent on longitude

Air storage bottle in hi-pressure pneumatic sys
A. Is a input device
B. Has pressure and return connection
C. Is generally make of steel alloy

[ولد قطر]

con. Module 11
1) A.method of helping to prevent aquaplaning is by fitting tyres which have:
a.A plain tread
b.Twin contact
c.Water dispersing treads.

2) distance over 250 miles we used
a.VLF
b.HF
c.VHF

3)Toilet recirculation fan u/s in flight
a.can be overcome by thermal ??? device.
b.close toilet until landing
c.can use as the toxic chemical toilet.

4)ACMS QUICK ACCESS RECORDER
a.must use digital tape
b.tape must not be use before
c.can use previous if first bulk erase.

5)Autopilot when approach Landing how many axis do we need?
a.2
b.3
c.4
6)Lube thread oxygen using
a.Teflon tape
b.WD40
c.hellerene
7)what is run back ice?
a.glaze ice
b.rime ice
c.glime ice

[ولد قطر]

Module 2 Physics

1) The gyroscopic principle of "Rigidity" operates on:
a. Newton’s 3rd Law
b. Newton’s 2nd Law
c. Newton’s 1st Law

2) Water is:
a. An Element
b. A compound
c. A mixture

3) Dew point is:
a. The Temperature at which condensation actually occurs
b. The Temperature at below which condensation occurs
c. The Temperature at above which condensation occurs

4)Fibre Optics operate on the principle of:
a.??
b. Total internal reflection
c.??

5)In a concave mirror, If an object is placed between the focal point and the
pole, the image will be:
a. Real, Inverted and larger
b. Virtual and on the opposite side
c. Real, erect and diminished

6)For a fixed mass of water at sea level ISA conditions and at 10,000ft:
a. The water will boil at a higher temperature than sea level
b. The water will boil at the same temperature as sea level
c. The water will boil at a lower temperature than sea level

7)An atom that has lost an electron is:
a. Positively Charged
b. Negatively Charged
c. It possesses no charge

8)Young’s modulus of elasticity is:
a. Stress multiplied by Strain
b. Stress divided by strain
c. Strain divided by stress

9)100Kelvin in degrees Celsius is:
a.-173
b.273
c.100

10)842 degrees Fahrenheit is equal to:
a.400 Degrees Celsius
b.450 Degrees Celsius
c.232.2 degrees Celsius

11)Which of the following is an example of a Longitudinal Wave
a. Sound Wave
b. Light Wave
c. Radio Wave

12) An astronaut blasting off from Earth experiences a G-Force of?
(Take g as 9.8 m/s/s)
a.5g
b.6g
c.7g

13) A ball is dropped from rest. What is its speed after 4 seconds? (Take G
as 10m/s.s)
a. 20m/s
b. 40m/s
c. 80m.s

That’s all I can remember at present but will try get more. There were a lot
of questions bases on the Pressure=Force/Area equation and also manipulating
formula in general. I have also included past questions from Shannon Aerospace
Physics exam in the past.

1) Compound are made up of:
a. elements in fixed ratios
b. substances which retain their original form
c. two or more substances mingled together

2) A ball is dropped from rest. What is its speed after 3 seconds?(take G
as 10m/s.s)
a.90m/s
b.45m/s
c.30m/s

3)A lifting machine moves an effort a distance of 200cm in order to raise a
load by .5m.The Velocity Ratio is:
a.0.25
b.4
c.40

4)A force of 15N is needed to move a body of mass 30kg along a footpath with uniform
velocity. Find the coefficient of Dynamic Friction:-(take g as 10m/s.s)
a.1/20
b.1/2
c.20

5)A motorcycle of mass 400kg is moving at a velocity of 8m/s.Calculate its momentum:
a.320 kgm/s
b.3200 kgm/s
c.50 kgm/s

6)The specific gravity of Meths is 0.8.Its density is:
a.800kg/m3
b.800g/m3
c.80kg/m3

7)The density of CU is 8,900kg/m3,what is its relative density:
a.8.9
b.89
c.890

8)How does the viscosity of a liquid change with temperature:
a. viscosity of a liquid increases with increasing temperature
b. viscosity of a liquid decreases with increasing temperature
c. Viscosity of a liquid does not change with temperature

9)Which of the following 2 points are equal:
a.40 degrees C and 40 degrees F
b.-32 degrees C and 0 degrees F
c.-40 degrees C and -40 degrees F

10)When is the only time a concave mirror forms a virtual image:
a. when the object is placed at the centre of curvature
b. when the object is at the focus
c. when the object is inside the focus

11)A convex mirror forms a virtual image when:
a. the object is inside the focus
b. always
c. the object is at the centre of curvature

12)Two Vectors are at 90 degrees to each other having magnitudes of 3N and
4N.The resultant is:
a.5N
b.7N
c.1N

13)What is 100 degrees Centigrade in Fahrenheit:
a.30 Degrees
b.148 Degrees
c.212 Degrees

14)What work is done if a force of 100N moves a body 15metres:
a.0.15mJ
b.1500kJ
c.1.5kJ

15)Which of the following has no units:
a. Stress
b. Strain
c. Elasticity

16)A Concave mirror is used for:
a. Headlights
b. Rear View Mirror
c. Periscope

17)What is the wavelength of a note of frequency 1kHz when its velocity is
340m/s:
a.0.34m
b.3.4m
c.0.34km

18)If the speed of a gyro is increased, the force required to precess the gyro
is:
a. Increased
b. Decreased
c. Remains the same

Module 5
1) EADI sky and ground display is provided by
A) synthetic TV signals
* B) raster scan
C) stroke pulse

2) A NOR gate with both inputs inverted becomes a
A) NAND gate
*B) AND gate
C) OR gate

3) An ARINC 429 binary coded decimal data word occupies bits
A) 11 to 29
*B) 11 to 28
C) 1 to 8

4) Requirement for software control
*A) AWN 45
B) JAR OPS
C) JAR AWO

5) What kind of light is used in fibre optic cable
*A) Infrared
B) Visible
C) Ultraviolet

6) CRT horizontal beam control is achieved by a
A) square wave
*B) sawtooth wave
C) sinusaidal wave

7) EICAS provides the following
A) engine parameters only
*B) engine parameters and syst warnings only
C) engine parameters and engine warnings only

8) engine parameters are displayed on
*A) ECAM
B) EHSI
C) FMSI

9) If a signal has a quantity in volts and a physical position it is
A) digital
B) synchronous
*C) analogue

10) Primary colors of CRT are
*A) red,green and blue
B) red,green and yellow
C) red blue and yellow

11) Before an IRS can complete the alignment sequence
A) the shutdown present position must be entered
*B) the current present position must be entered
C) either the last or current position must be entered

12) ARINC 629 periodic mode is used for
*A) normal operation
B) transforming data only on events impt to aircraft operation
C) database loads

note: letters with * are ans

[أحمد سعيد عبد الرازق]

شكرا جزاكم الله خيرا

[handsome_devil]

مشكووووووور اخي و جزاك الله الف خير


بارك الله فيك

[handsome_devil]

هالموقع بعد فيه بعض الاسئلة لبعض الmodules

http://ndhome.netvigator.com/~thw552fhh/Licence_Revision/MCQ_practice.htm

[ولد قطر]

موقع رائع مشكور اخوي Handsomeوأتمنى من باقي الشباب المشاركه


تحياتي

ولد قطر

[R-TUNE]

شكرا للجميع

[عبد الله الحاج]

مشكورين شباب

[Hassn166]

مشكور اخوي

[B773]

وعليكم السلام ورحمة الله وبركاته
شكرا لك اخوي ولد قطر على الموضوع الجميل جداً
واتمنى الفائدة لأصحاب الأختصاص منه
بالتوفيق أن شاء الله